NVH Analysis & Problem-Solving Framework
Diagnose and solve automotive noise, vibration, and harshness issues systematically
What You Can Do
You can systematically investigate NVH complaints, conduct root cause analysis using transfer path analysis methodologies, plan and interpret diagnostic testing data, and develop evidence-based solutions across the full vehicle lifecycle. This framework guides you through multidisciplinary analysis—covering acoustics, mechanical dynamics, materials, and manufacturing variability—enabling faster problem resolution and more effective cross-functional communication with design, manufacturing, and supplier teams.
Features
structured diagnostic approach to pinpoint NVH sources rather than intuitive guessing
methodology to isolate path contributions from sources through structures to receivers
protocols for analyzing dyno, track, and wind tunnel test results to identify frequency-dependent problems
systematic templates for designing in-cabin and exterior pass-by noise, vibration acceptance testing
criteria and methods for assessing suspension, drivetrain, and trim components for NVH suitability
alignment with WLTP, EPA, and regional noise legislation requirements
frameworks for conveying NVH findings to design, manufacturing, and supplier teams
Example Output
Example 1: Door Rattle Diagnosis
- Problem: Interior buzz at 2,500–3,500 RPM during acceleration
- Framework Output: Diagnostic sequence identifying loose trim panel clips, resonance frequencies, and transfer paths; recommended inspection checklist and reinforcement solutions
Example 2: Powertrain Noise Investigation
- Problem: Elevated engine noise at idle post-production
- Framework Output: Test planning matrix for dyno analysis, frequency analysis protocol, supplier component evaluation checklist, and validation test requirements
Example 3: Wind Noise Reduction
- Problem: Pass-by noise exceeds target by 3 dB
- Framework Output: Transfer path analysis plan, seal/weatherstrip assessment methodology, acoustic material placement guidelines, and prediction model validation steps
What's Included
- SKILL.md: core NVH analysis framework and diagnostic methodology
- Root Cause Analysis Checklist: systematic diagnostic sequence for complaint investigation
- Transfer Path Analysis (TPA) Template: planning and execution workflow for isolating path contributions
- Test Data Interpretation Guide: protocols for dyno, track, and wind tunnel analysis
- Supplier Component Evaluation Criteria: assessment matrix for NVH-critical components
- Regulatory Compliance Mapping: alignment reference for WLTP, EPA, and regional noise standards
Who It's For
- NVH engineers — developing noise and vibration targets and solving complex multidisciplinary issues
- Automotive engineers — troubleshooting NVH problems during design validation and production ramp-up
- Warranty and field service teams — investigating customer complaints and warranty claims systematically
- Acoustics specialists — planning and interpreting transfer path analysis and noise source identification studies
- Quality and manufacturing engineers — addressing NVH issues during production and supplier quality audits
Best For
- Root cause diagnosis of customer NVH complaints and warranty claims
- Transfer path analysis planning and noise source isolation studies
- Diagnostic test design and engineering build validation testing
- Supplier component NVH evaluation and performance assessment
- Pre-launch NVH validation and regulatory compliance verification
- Dyno, track, and wind tunnel test data interpretation and frequency analysis
- Cross-functional NVH problem-solving during design, engineering, and production phases
You might also like
You can pinpoint the exact source of sensor fusion failures—whether they stem from misaligned camera/LiDAR/radar extrinsic calibration, timestamp desynchronization, data validation gaps, or algorithmic issues. This skill decomposes multi-modal perception errors into sensor-specific contributions and generates quantifiable diagnostic reports that directly guide calibration and testing teams toward fixes rather than blind troubleshooting.
You can decode SAE J2012 standard CAN diagnostic trouble codes (P, B, C, and U codes) with manufacturer-specific extensions, analyze multi-frame fault sequences and temporal patterns across multiple modules, and generate structured diagnostic hypotheses that differentiate between electrical, communication, and algorithmic failures. This skill transforms raw DTC data into actionable investigation vectors, reducing diagnostic analysis cycles from hours to minutes while improving root cause accuracy.
You can quantify sensor fusion performance across object detection, classification, tracking, and localization using standardized metrics. The framework helps you identify systematic failure modes in diverse environmental conditions, document safety-critical gaps, and generate structured evidence packages for ISO 26262 and SOTIF compliance. This enables you to benchmark sensor configurations, define perception KPIs, and support regulatory submissions with rigorous performance documentation.
You'll establish validated simulation architectures that execute cleanly and produce physically meaningful results. This skill guides you through model topology decisions, solver parameter selection, constraint formulation, and pre-run validation checkpoints. You'll identify and eliminate configuration errors—improper contact stiffness, inconsistent degrees of freedom, poorly scaled inertia properties—before wasting CPU hours on failed simulations.
This skill systematically validates your OTA update architecture across five critical dimensions: partition and storage allocation for A/B slots and recovery images, safety and rollback mechanisms including atomic commit strategies, delta compression efficiency for cellular bandwidth optimization, regulatory compliance mapping against ISO 26262 and UN R156, and deployment risk identification including version conflicts and single points of failure. You identify architectural gaps before they cause field failures or fleet immobilization.
You can rapidly correlate vehicle test data (lane change, slalom, ramp steer) with simulation targets, troubleshoot steering feel complaints like heaviness, dead band, and kickback, and analyze how suspension geometry, EPS control strategies, and column stiffness modifications affect handling behavior. This skill organizes complex multi-domain steering data into actionable insights that connect theoretical kinematics to driver feedback.
You can analyze embedded diagnostic code across five critical domains: CAN message parsing and protocol compliance, Diagnostic Trouble Code (DTC) generation logic, diagnostic state machine transitions, sensor fault detection thresholds, and diagnostic data link command handlers (UDS/KWP). The skill identifies logic errors, false-positive configurations, state transition gaps, and compliance deviations that would otherwise only surface during expensive dyno or road testing.
You can transform raw accelerometer data, sound pressure measurements, and frequency spectra into structured diagnostic insights. Claude helps you organize test data, interpret Campbell diagrams and waterfall plots, quantify source contributions through transfer path analysis, and correlate physical measurements with customer complaints. This systematic approach replaces intuitive troubleshooting with hypothesis-driven test plans and targeted solutions.